Plumbing for Beginners: What You Need for Installing a Bathtub
Plumbing for Beginners: What You Need for Installing a Bathtub
Blog Article
We've stumbled upon this article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and decided it made sense to discuss it with you here.
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately challenging project. If the old tub is easily accessible, the project can relocate rapidly; if you need to open up a wall surface to eliminate the old tub as well as place the brand-new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and also set in the brand-new one. Make sure you have qualified on your own for the job and fit trying it. Rather than working with a professional to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a new tub in your restroom if you have actually currently purchased a new tub and don't need to transform the arrangement of your previous supply of water pipes.
Your devices and also product checklist must comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, switch on the taps to drain any water staying in the system. The procedure of eliminating the existing taps can be rather problematic due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin making sure that the washers are in location in between the tap as well as the sink. Safeguard the faucet in place with the maker provided backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The previous kind must be connected to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the required position. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bath tub till the level reviews level.
To set up taps, fit all-time low of the outermost versatile faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water and also check all joints and new pipework for leaks and tighten them if needed. Fill the bathtub and additionally inspect the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait up until the bath tub has actually been made use of a minimum of once as this will resolve it right into its final position.
Preparing for the Installment
To start with, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, causing the water to permeate the wall surface in between the bath and also the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealant can crack fairly early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I hope you enjoyed reading our article about Tools You Need to Install a New Bathtub . Thanks a ton for taking the time to browse our piece. Sharing is caring. Helping people is fun. Thanks a bunch for your time. Kindly visit our website back soon.
Plumbing woes? Connect. Report this page